Tiling Tips – Tips and Information About Tiling

Real Stories from the World of Tile, Stone and Grout Maintenance

Author: Reese Mackie

Marble Posts 

Polishing Marble Wall and Floor Tiles in Suffolk

Reese Mackie 0 Comments , , , , , , ,

Not too long ago I was called down to a house in the small village of Elmswell, Suffolk. I was asked to take a look at a Marble floor and wall tiles which had become dull and lifeless over time, especially in high traffic areas and now need to be burnished to bring the polish back. In addition, my client was unhappy with the beige colour of the grout lines, requesting that I change the colour to white following the clean and polish. Cleaning and Polishing a Marble tiles To get the floor clean and bring back the polish I used a set of four diamond encrusted burnishing pads which have different levels of grit, applied to the Marble tiles with a small amount of water. I started with a Coarse pad, before moving on to a Medium pad, a Fine pad, and finally a Very Fine pad to achieve the desired polished look. The floor was given a thorough rinse between each pad in order to remove any excess residue that had resulted from the burnishing process. Once I had finished the floors I moved onto the Marble wall tiles in the bathroom where the same process was repeated, for wall tiles however you need to use the smaller six inch burnishing pads fitted to a hand held buffer. Sealing Marble Floor Tiles I left the floor to dry for a few days before returning to seal it for which I used Tile

Read more…

Read more
Marble Posts 

Polishing Marble Wall and Floor Tiles in Shropshire

Reese Mackie 0 Comments , , , , , ,

For this job I travelled to the town of Albrighton, which is actually the most easterly settlement in the whole of Shropshire. My client had an issue with their Marble tiled floor which was installed in the kitchen and hallway. They had dropped and broke a bottle of vinegar in the kitchen, and the substance unfortunately came in contact with the tiles. Since Marble is highly sensitive to acid, the vinegar (an acetic acid) had basically etched the surface of the tiles make it impossible clean chemically. Although the tiles were a nice, expensive Marble, the person who had first installed them had done a poor job, leaving lippage of up to 5mm in some areas, which would make work trickier. Undeterred I could see it would be possible to restore the floor using a combination of burnishing for the tiles and cleaning with a high alkaline product for the grout lines. I demonstrated this to my client on one tile which went well and I was then given the go ahead to restore the entire floor. Cleaning and burnishing acid damaged Marble tiles My first task focused on cleaning the grout lines using a solution of Tile Doctor Pro-Clean worked in with a stiff grout brush. Pro-Clean is a high alkaline cleaner suitable for use on most types of natural stone floor. It helped to alleviate most of

Read more…

Read more
Marble Posts 

Maintaining Marble Tiled Floors

Reese Mackie 0 Comments , , , , ,

The photographs before are of Marble floor installed in the kitchen of a house in Melton Mowbray, that we recently refinished. The honed matte marble tiles had previously been finished with a water-based topical floor sealer by the customer to create a polished finish; unfortunately the coating had become damaged, worn and now soiled. To restore the finish with something more durable we recommended the removal of any remaining coatings, then re-finishing with our restorative diamond encrusted burnishing pad system and then re-sealing with an impregnating rather than topical sealer. Our quote was accepted and we returned on the agreed date to restore the floor. Deep Cleaning Marble Tile and Grout The first step was to remove the old coating and clean the grout using a strong dilution of Tile Doctor Pro-Clean which is a strong alkaline formula that is safe to use on stone. The solution was scrubbed into the grout using a stiff brush and also worked into the Marble floor using a rotary machine fitted with a black scrubbing pad. The now dirty cleaning solution was then rinsed away using water and extracted with a wet vacuum. Burnishing a Marble Tiled Floor The next step was to burnish the floor using a set of Tile Doctor burnishing pads starting with a coarse pad to strip the

Read more…

Read more
Marble Posts 

Stained Marble Tiled Floor Renovated in Berkshire

Reese Mackie 0 Comments , , , ,

Never judge a tiled floor by its appearance! On this particular occasion, I visited a client at a house in the village of Streatley which is a small village that sits alongside the River Thames as it runs through the county of Berkshire. The requirement was to take a look at a very old Marble floor which was initially believed to consist of Victorian, rather than Marble, tiles due to the pattern. My client simply could not get the white Marble tiles looking their best; many were a displeasing off-cream colour and naturally wanted them looking new again. Before beginning the restoration, we confirmed that the stone was actually Marble. We did this by testing the tile with acid, which the tiles responded to since Marble is naturally acid-sensitive. Additionally, we could also see the veins running through the tiles, which you simply would not get with a Victorian tiles. Burnishing a Marble tiled floor Chemical cleaning had no effect on this floor, so it’s understandable that my client’s attempts at cleaning with everyday household products were unsuccessful. With this type of stone the only method would be to burnish the floor with a set of diamond encrusted pads. I started off by using a Medium 800 Grit burnishing pad to no avail, followed by a Coarse 400 Grit burnishing pad,

Read more…

Read more
Marble Posts 

Tumbled Marble Floor Refreshed in Twickenham

Reese Mackie 0 Comments , , , ,

Marble tiles can be tumbled in large drums to achieve an aged and softened effect, and this can look very nice providing that the stone is adequately maintained. In the case of this floor at a property in Twickenham South West London, the Marble tiles that had been laid over five years ago, and in that time the sealer had worn down offering the floor little protection. Dirt had now become ingrained in the pores of the stone and grout, and a deep clean and fresh seal were required to restore the stone’s original colour and lustre. The property owner asked me to complete the job and I was more than happy to oblige. Cleaning Dirty Tumbled Marble Tiles To begin the restoration, I applied both Tile Doctor Pro-Clean, which is a high alkaline cleaner, and Tile Doctor Remove and Go, which a heavy-duty stripper and remover, to the floor and scrubbed the products in using a scrubbing pad fitted to a professional rotary machine. The chemical solvents in the Remove and Go helped to break down any old sealer that remained inside the stone, allowing the Pro Clean to then work its magic on the stubborn ingrained dirt the customer had struggled to remove previously. Some of the deeper veins and grout lines I chose to scrub by hand to ensure the fullest and most meticulous clean possible.

Read more…

Read more
Marble Posts 

Edwardian Marble Floor Restoration

Reese Mackie 0 Comments , , , , , , ,

Windlestraw is a picturesque Edwardian manor hotel overlooking the Tweed Valley, near Walkerburn in the Scottish Borders area of Scotland. One of the bathrooms in the manor was in the process of being refurbished when two layers of floor tiles were removed, unveiling an original Marble tiled floor dating back to the 1920s. After the top layers of tile had been removed the Marble was still covered in old adhesive and cement and although Marble is known for its quality and durability the hotel owner didn’t want the building contractor to proceed any further in case they damaged it. The owner was keen to restore the Marble floor as an original feature so we were called in to set the situation right. Refurbishing a Marble Tiled Bathroom Floor To restore the floor I used two processes known as milling and burnishing. Milling literally involves grinding down uneven or rough surfaces using very coarse, diamond encrusted pads. The pads are usually used to resolve lippage issues on natural stone but in this case we needed to use the very coarse abrasive pads to grind off the adhesive and cement. I used a set of three coarse milling pads rinsing with water between each pad and starting with a 50 grit pad, before moving on to 100 and 200 grit pads. This process was very effective and

Read more…

Read more
Marble Posts 

Antique Marble Lamp Base Restored in Fife

Reese Mackie 0 Comments , , , , ,

At this property in Fife, I was asked to restore not a tiled floor, but in fact a solid black Marble lamp base. The lamp base was particularly by scratched and damaged as a result of a lack of care and consideration by a removal company. It’s a shame to see such a high-quality item suffer this kind of damage; nonetheless, I was keen to help with restoring it back to looking its best. I arranged to collect the base the next time we were working in the area of Fife, a historic area of Scotland which houses St. Andrew’s, one of the world’s oldest universities. The customer and I agreed that I would drop it back a week later following the restoration. Restoring a Damaged Black Marble Lamp Base Restoring the appearance of the Marble (and other high-end stones such as Limestone) commonly requires a process known as burnishing. To begin, we applied to the base the first of a set of four six-inch burnishing pads. This pad, which had a Coarse grit, was fitted to a small handheld buffing machine and used to burnish the Marble with a little water for lubrication. I then worked my way through the pad system to apply Medium, Fine and Very Fine grit burnishing pads. The process gradually improved the appearance of the base, managing to remove some of the lighter scratches; however, it

Read more…

Read more
Marble Posts 

Polishing Marble Tiles following Installation

Reese Mackie 0 Comments , , , ,

These Marble tiles were installed at a lovely property in North Ferriby by another tile company who although has done a great job laying the floor had neglected to provide the owner with any kind of post-installation maintenance. Thus the tiles, which covered a large kitchen and hallway area, appeared dull and certainly not up to the standard that could be achieved with the right methods. Funnily enough, the tile company had told the property owner that the stone would need to be sealed, but did not offer to carry out the process themselves. After conducting their own research, the property owner contacted her local Tile Doctor to see what could be done. I came round to inspect the floor and recommended the floor was polished through a process known as burnishing, followed by the application of a sealer to provide durable protection for the stone. Burnishing a Marble Tiled Floor Burnishing involves the application of diamond encrusted pads with different levels of grit. At Tile Doctor we work with a four pad system that allows us to gradually refine the polish on suitable tiled floors, including Marble and Limestone. I started the process by applying a Coarse grit burnishing pad across the entire floor lubricated with a little water, the 17 inch pads fit a rotary floor

Read more…

Read more
Marble Posts 

Deep Cleaning a Stained Marble shower enclosure in South Wales

Reese Mackie 0 Comments , , , , ,

Tiled shower cubicles can very easily become tired and grubby looking without the right care. The shampoos and soaps we use in our everyday lives can have long lasting damage if their effects are not sufficiently dealt with, with grout mould being a very common problem for property owners in the UK where we have a cold climate that encourages us to seal up our homes limiting natural ventilation. At this property in the small village of Beddau, near Cardiff, my customer had a particularly poorly maintained Marble tiled shower cubicle suffering from bad staining. Since Marble is an acid-sensitive stone it is especially vulnerable to damage when exposed to even slightly acidic shower products. The grout was also in a bad way, having turned from a pleasant off white colour to black. The entire area was now well overdue from some attention from the Tile Doctor. Cleaning a Marble Tiled Shower Cubicle To begin the restoration of these tiles I had to remove any old sealer. I did this by applying a combination of Tile Doctor Pro Clean, which is a versatile cleaner, stripper and degreaser, and Tile Doctor NanoTech HBU, which is a more powerful product designed for the removal of heavy soil buildup. As the old sealer came away, I left the two products to soak into the tiles to lift

Read more…

Read more
Marble Posts 

Putting the Shine Back on a Marble Vestibule Floor

Reese Mackie 0 Comments , , , , ,

A fantastic Marble tiled entrance hallway is the first thing you see when you open the door to this property in Congleton. Unfortunately, polished stone does need regular maintenance to keep its appearance, especially in high traffic areas such as this vestibule which had lost their shine, leaving them looking dull and unexceptional. Needless to say, the property owner was keen to get the floor restored to its former glory. That’s where I stepped in. Cleaning and Burnishing a Marbled Tiled Entrance Hall There was no evidence of old sealers present on the floor, so I started deep cleaning the tiles and grout lines using a solution of Tile Doctor Pro Clean mixed with clean water. A quick word on cleaning here, as an alkaline-based cleaner, Tile Doctor Pro-Clean is suitable for use on natural stone floors, including acid-sensitive stone such as Marble and Limestone. Many everyday household cleaners from the supermarket are acidic, which will erode the life of the sealer and a strong acid can etch the surface of sensitive stone, so make sure to source the correct cleaning product to avoid this problem. The cleaning solution was left to soak into the tiles for ten minutes before being worked in to give a thorough clean using a rotary machine fitted with a scrubbing pad. The

Read more…

Read more
Marble Posts 

Marble Tiles Restored After Being Etched With Cillit Bang

Reese Mackie 0 Comments , , , , ,

Here at Tile Doctor we can’t stress often enough how careful you have to be when choosing a cleaning product for use on natural stone. Acid bases cleaners in particular can etch the surface so always read the label before buying. Unfortunately, this customer, who lives in Twickenham, learned this the hard way. Limescale build-up on shower tiles can be an unsightly problem in hard water areas and this customer’s house cleaner had attempted to treat it with Cillit Bang on their Marble tiled shower room floor. Whilst good at removing Limescale on ceramic tiles, the product is acid-based and in this case caused severe etching to the surface of the Marble. This customer is not the first to experience this problem with Cillit Bang and we have looked into this before and I can confirm it does say on the back on the bottle that you should not use it on all natural stone including Marble and Granite. The mistake had really damaged the appearance of this lovely floor however the good news is etched Marble can be refinished and we do offer this service. Fortunately, this customer found us on-line and called us in to rectify the problem as Burnishing a Marble Tiled Shower Room Floor With high quality, acid-sensitive stone we find that rather than cleaning with a liquid product, it is

Read more…

Read more
Marble Posts 

Deep Cleaning and Polishing a Marble Tiled Kitchen Floor

Reese Mackie 0 Comments , , , , ,

When you have high quality tiles like Marble, Limestone and Travertine, it’s even more important than normal to use suitable cleaning products. If, for example, you apply a slightly acidic cleaner to Limestone, it can cause severe, irreparable etching that significantly damages the appearance of the stone. In a similar way, this customer in Penrith had been using an unsuitable wax-based liquid soap to clean her “Crema Marfil” Spanish Marble kitchen tiles. It had failed to prevent a heavy buildup of dirt, and had in fact darkened the stone, leaving it looking stained, unnatural, and all-around difficult to clean. To avoid the floor becoming a complete nuisance, the customer contacted me to see what could be done to alleviate the problems. Burnishing a Dirty Marble Tiled Kitchen Floor I explained to the customer that a process we use at Tile Doctor known as burnishing would be the most effective way to clean the Marble. Also suitable for Limestone and Travertine, this process involves the sequential application of specialist diamond encrusted pads of different grits to grind down any soil buildup and gradually create an aesthetic polish in the surface of the tiles. Our system consists of four burnishing pads: Coarse, Medium, Fine and Very Fine. I started, using a little water

Read more…

Read more
Marble Posts 

Renovating White Tumbled Marble Tiles

Reese Mackie 0 Comments , , , , ,

This White Tumbled Marble tiled floor at a house in Hampton had been installed throughout the kitchen and dining area ten years back and was now in desperate need of a deep clean and seal to remove dirt that had accumulated in the pores of the stone. Once the dirt gets into the pores it makes it difficult to keep clean which is exactly the problem the property owner had experienced. The ‘tumbled’ effect on the Marble is achieved by tumbling the tiles in drums to soften and age the edges and surface of the stone. However, it was difficult to appreciate this interesting style as the presence of dirt and staining was quite overwhelming and the owner was now keen to restore it back to its original condition. Cleaning Tumbled Marble Tiles I started the restoration by applying a strong dilution of Tile Doctor Pro-Clean. This high alkaline cleaning product was spread across the floor and left to dwell for a short period, before I then worked it deep into the pores of the stone using a heavy duty rotary scrubbing machine. Next, some of the stubborn, more deeply ingrained stains were scrubbed by hand, along with the grout lines, which were also particularly dirty. The resulting slurry of water and cleaning solution was then pressure rinsed away and soaked up with a wet vacuum. The

Read more…

Read more