Victorian Hallway Tile Maintenance in Surrey
Details below of a tired and lifeless looking Victorian tiled hallway that I was asked to deep clean and seal
Read more
Author: Reese Mackie
Marble Tiles restored in Busy London Corridor
This Marble tiled floor was installed in the corridor of a very smart block of apartments in the Victoria area of Central London. The corridor was the main access route in and out of the apartment block and was constantly being used by residents, as a result there was a lot of foot traffic and decorators had contributed to the state of the floor which was now looking worse for wear with dirt, varnish and paint spots. Having struggled to get it clean the managing agent was considering replacing the floor, that was of course until the contacted us. Cleaning Marble Tiled Floors To remove the paint and varnish we used Tile Doctor Remove and Go which is an effective coatings remover designed for use on most types of tile and stone, we left it to soak and penetrate into the floor for 45 minutes before scrubbing it into the floor with rotary machine fitted with a black pad scrubbing pad followed by a hot water rinse to remove the cleaner. We followed this with the application of 1 to 4 dilution of Tile Doctor Pro-Clean again scrubbed in with a scrubbing pad; Pro-Clean is a Cleaner and Stripper so this step removed any remaining sealer and dirt from the Marble floor. Last step was to wash the tile down again to remove any chemical and neutralise the floor. Polishing Marble Tile The
Read more
Large Victorian Hallway Deep Cleaned and Sealed near Daventy
The pictures below were taken of a Victorian tiled hallway floor in a large property in the old village of
Read moreMarble Tile Polishing in Buckinghamshire
A customer recently purchased a property the village of Chesham and hoped we could improve the appearance of her textured marble tiled floors which had over a number of years become dull and lost the polished marble look one would expect from a floor of this quality. Marble Tile Cleaning and Polishing For polished stone like Marble and Limestone the only way to restore the finish is to burnish the floor and this floor was no different. The burnishing pads are diamond encrusted and come in a setup of four seventeen inch pads for use with a heavy rotary machine, each pad having a different purpose. So we started with the Red pad which is designed to remove sealers together with a little water, we then took the opportunity to clean up the grout by applying a dilution of Tile Doctor Pro-Clean and scrubbing it into the grout lines to get them clean. Next step was to remove the soiled cleaning solution and wash the floor down with water before moving onto the white burnishing pad which will grind off ingrained dirt and is the first step in polishing the floor. We then completed the floor polishing using the Yellow then Green polishing pads which smooth down the surface and produce a shiny finish. Sealing Textured Marble Tiles Once the floor was polished we applied Tile Doctor
Read moreCleaning and Polishing Marble Tiles
These photographs were taken at a house in Ealing, West London where the customer had requested a deep clean and polish of the marble tiled floors installed in a kitchen and conservatory which had become dull and dirty over a period of time. Marble Tiled Floor Polishing The first step was to give the Marble floor a thorough clean throughout with a medium dilution of Tile Doctor Pro-Clean which is an industrial strength Tile Cleaner safe to use on natural stone floors, we also took this opportunity to use a stiff brush along the grout lines to get them nice and clean, the soiled cleaning solution was removed using a wet vacuum and the floor rinsed with clean water. The next step was to use a set of diamond encrusted Twister Burnishing Pads fitted to a rotary buffing machine to polish the floor. The pads come in a set of four; you start with the Red pad together with plain water and this cuts through and removes surface grime and any surface seal. You then progress through one by one until you get to the final Green polishing pad which provides a high polish, we managed to complete most of this process before the end of day. Polishing and Sealing Marble Tile The next day we completed the polishing process with the Green pad which really brought a deep shine to the floor. To
Read moreMultiple Marble Wall And Floor Tiles Cleaned
This job was to refresh the Marble tile installed in a house in Woking. There were a number of different marble tiles installed on the wall and floor including two shower cubicles, a bathroom floor, a small cloakroom floor and the kitchen floor; the pictures below show before and after photographs for each job. Cleaning a Marble Tile Shower Cubicle I started with the shower cubicles using Tile Doctor Oxy-Pro which is a specific product for cleaning showers and comes with a spray attachment that mixes the cleaning agent with air making it lighter and helping it stick to vertical surfaces. This was left to dwell on the surface for a while and then the tiles were scrubbed before being rinsed down. This action not only cleaned the dirt and soap scum off the tile it also got rid of some mould that had started to grow. In one shower there was a build-up of limescale on the wall so to get rid of this I used a little Tile Doctor Grout Clean-up, this product is usually for removing grout smears from tile however it’s also good at removing most types of mineral deposits such as Limescale, you do have to be quick though as it’s an Acid based product I had to be quick and to thoroughly rinse because I didn’t want to damage the marble. Marble Mosaic Bathroom floor tile cleaning The next
Read more
Restoring old Church Steps in Gloucestershire
Tewkesbury, the town and civil parish in Gloucestershire, is famous for the Tewkesbury Abbey, a Norman abbey church dating back
Read moreRemoving Limescale from Tumbled Marble
This Tumbled Marble mosaic wet room floor was installed in a house in London, SE1 four years before prior and was now looking a little tired. This was mostly caused by a build-up of Limescale which had then become grimy. Stripping a Tumbled Marble Floor To treat the Limescale I used Tile Doctor Grout Clean Up which managed to remove most of the scale and to remove the remainder I steamed the tiles using an Earlex Steamer and carefully scraped any remaining Limescale residue away with a Stanley window scraper. To restore the marble itself I used Tile Doctor burnishing pads to re-polish the tiles using 17′ pads on the main area and 8′ pads on a hand-held Clarke polishing machine in the corners. These diamond encrusted pads come in a number of different colours and are applied one after another with each pad being a finer grade than the last. After thoroughly rinsing the stone again and removing the waste water with a wet vacuum. As the marble was naturally fast drying I used an Earlex heat gun to speed dry the floor and repeated this after lunch to ensure the floor was entirely dry before sealing. Sealing Tumbled-Marble Tiles Once the Marble tiles were dry I started to seal them using two coats of Tile Doctor Colour Grow sealer which is a great choice for natural stone as it
Read moreMarble Tile Restoration at a Neoclassical Palladian Mansion
This Marble tiled floor is located in the pantry of the historical Kinross House which is a late 17th-century country house overlooking Loch Leven that was built by the architect Sir William Bruce as his own home in 1686. You can see from the photograph the floor was in quite a state and given the history it was an honour to be asked to work on the floor. Marble Tile Cleaning and Polishing We brushed out the floor to remove all the loose debris and then proceeded to restore the floor using a set of diamond encrusted burnishing pads which fit a rotary buffing machine. The burnishing process is designed to grind out dirt in the stone and smooth /polish the floor, you start with a course pad and work your way through the four pad set until you get to the finer polishing pad. This may sounds simple but it does take time to complete. Sealing Marble Tiles Once the floor was polished we applied a couple of coats of Tile Doctor Pro-Seal which is a non-sheen premium sealer recommended for natural stone that provided the natural matte look the client was after and will protect the Marble and keep the floor looking good. Source: Marble restoration in Perth and Kinross, Scotland
Read more
Deep Cleaning Victorian Hallway Tiles in Middlesex
Apologies in advance but I forgot to take the usual before photograph of this Victorian tiled hallway in Twickenham that
Read moreDealing with Scratched Marble Floor Tiles
This Marble Tiled floor was installed in the conservatory of a house in Woodhall Spa who had asked if we could remove the scratches from their inherited marble tiles around the door area and where furniture had been dragged across the tile as shown in the photos. Interestingly our customer is a chief engineer on cruise ships all over the world and knew what this floor could look like if restored professionally. Burnishing Mable Tiles Other than the scratches the majority of the floor had been well maintained so the solution was to burnishing the marble back to its original condition using a set of diamond encrusted pads fitted to a slow speed machine and lubricated with a little water. The burnishing pads come in a set of four and applied to the floor with a little water one by one using a rotary machine running at slow speed. The process starts with the coarse pad which strips back the top layer and removes sealers and dirt from the surface of the stone. The pads then become finer and finer with the last pad being a final polish that takes the tile back to near it’s originally intended shine. You can see from the photographs that we actually managed to resurface the marble, remove the scratches and we also filled in some small holes and then allowed the floor to dry
Read more300m2 Marble Tiled Floor Cleaned and Polished
Following on from a referral from a Property Management company I paid a visit it to this palatial property in Oxshott which had approximately 300m2 of Marble tiled flooring that they wanted cleaning and re-polishing, my initial quotation to do this mechanically was too high so I offered an alternative using diamond encrusted burnishing pads which reduced the cost significantly. I didn’t receive an answer so I thought that was the end of it however five months later I got an email asking me to carry out the works. Marble Tiled Floor Polishing This was a very large area so we had two men working with burnishing pads in 10 metre sections. The pads come in a set of four; you start with the coarse pad together with a little water and this cuts through and removes surface grime and any surface seal. You then progress through the other finer pads one by one until you get to the final polishing pad which provides a high polish. Fortunately there were not many stains and the ones that were there came out quite easily. When we had completed a room using this system we then applied Tile doctor Shine powder which is a crystallising power worked into the floor using a white buffing pad and a little water; it adds an extra level of deep shine to the marble floor giving it that extra wow
Read moreMarble Tiled Kitchen Floor Cleaning
These Marble Floor tiles were installed in the kitchen of a house in Didsbury where a lot of building work had recently completed. You can see from the photograph that the tiles were stained and the grout had darkened. Marble Tiled Floor Polishing To improve the look of Marble it’s necessary to strip it right back and then polish which we are able to do with a rotary machine and burnishing pads. The pads come in a set of four; you start with the coarse pad together with a little water and this cuts through and removes surface grime and any surface seal. You then progress through the other finer pads one by one until you get to the final polishing pad which provides a high polish. Once this was done I got to work on the grout with a dilution of Tile Doctor Pro-Clean which was worked into the grout lines by hand using a stiff grout brush. The tile and grout was then rinsed down three times with clean water to remove any dirt. To give the floor the final finish Tile Doctor Shine powder was applied using a white buffing pad and a little water; the crystallising powder adds an extra level of shine to the Marble floor giving it that extra wow factor together and also gives it a tough durable finish. I can recommend this last step and certainly the customer was very pleased with
Read more
Restoring the Polish on Travertine Kitchen Tiles in Buckinghamshire
Travertine is a type of Limestone which unique and distinctive features, making it a highly sought after and expensive type
Read moreCommerical Marble Tiled Floor Restoration
Photographs below of a classic black and white Marble floor tile installation at premises in the city of Winchester. As you can see these Marble tiles had seen some traffic and were not in the best of condition following on from some building work that had been going on; fortunately we are quite used to dealing with these problem and have just the right products and equipment to restore them. Marble Tile Cleaning and Polishing For best results on hard stone surfaces such as Marble we burnish the floor using a set of diamond encrusted polishing pads. You start with a coarse pad which applied with a little water to remove surface dirt and sealers etc. before moving through a set of finer polishing pads until you reach a high shine glossy finish. Half way through the burnishing process we stopped to apply a dilution of Tile Doctor Pro-Clean along the grout lines and give them a scrub with stiff hand brushes repeating the process in stubborn areas. After the treatment the floor was washed do to remove any soiled solution before being buffed with a white buffing pad. Any trace of its previous condition was now gone and the floor was uniform in appearance, it took much of the day to do the polishing and a set of four burnishing pads to acquire the right lustre. Source: Mabrle
Read moreResolving Marble Tile Installation Issues
These photos are from a newly installed Polished Marble floor in the kitchen at a residence in Irthlingborough Northants which had been left covered in grout haze. The customer called the builder back as they were unhappy with the finish but he could not rectify the problem, so the customer contacted Tile Doctor to see if anything could be done. This is a problem we often come up against where a builder or tiler does a good job of laying the tiles but for some reason doesn’t remove all the grout from the tile and we have even seen some jobs where the grout smears have been sealed over which makes it even more noticeable especially on a polished floor. Fortunately for the customer we are able to resolve such problems and after agreeing the process we set about solving the problem. Burnishing Polished Marble Tiles To protect the kitchen units from any splashing etc. all the kick boards were removed and plastic sheeting fitted to protect new doors and panels before any work was undertaken. Polished Marble is a very hard surface that has to be burnished with diamond encrusted pads to restore the finish so we set about this task using a set of Tile Doctor Burnishing Pads. The pads come in a set of four, you start with the coarse pad together with a little water and this cut’s
Read moreScratched Marble Floor Tiles Restored
This was a Marble tiled floor installed in the kitchen of a house in Olney, Bedfordshire which had been scratched in places and was now overdue for some TLC. Cleaning Marble Tile and Grout The first job was to give the floor a general clean using a dilution of Tile Doctor Pro-Clean which was left to dwell on the Tile and Grout for a short while before being worked in with a rotary machine fitted with a scrubbing pad and a stiff hand brushes along the grout lines. The floor was then washed down with clean water to remove the soiled cleaning solution with the liquids being removed using a wet vacuum. Burnishing and Polishing Marble Tile To restore the original finish and remove the scratches the floor needed to be cut back using a set of diamond encrusted burnishing pads. The pads come in a set of four and you start with the coarse pad and a little water and then move on to the Medium, Fine and Very fine pads at which point the surface looks immaculate and polished. The next task was to protect the floor and bring up the appearance even further by applying Tile Doctor Shine Powder which is polished into the floor using a buffing pad; the powder add a really deep finish to the appearance of the Marble and hardens on the surface to provide durable surface protection. Hopefully
Read morePolishing Tumbled Marble
This 50m2 Tumbled Marble tiled floor in Dewlish, near Dorchester had not been deep cleaned and re-sealed for at least five years and showed signs of the normal wear and tear associated with a busy kitchen/dining room and a dog that enjoyed muddy walks. The old sealer was now breaking down allowing dirt to become ingrained in the Marble making it difficult to clean. Stripping a Tumbled Marble Floor To restore the surface finish it needed to be burnished using a set of diamond encrusted burnishing pads. The pads come in a number of different grades from coarse (used to strip off sealers and dirt from the Marble) too very fine (used for final polishing) and are applied one after another starting with the coarse pad and moving through to the very fine pad towards the end. Each stage requires a little water which captures the soil and is rinsed away and removed with a wet vacuum. This process completely removed the old sealer and surfaces scratches with a new shine. The floor was given a thorough wash down at this point again using a wet vacuum to remove as much water as possible from the surface before leaving it to dry for the evening. Sealing Tumbled-Marble Tiles The next day the Marble had dried and I started to seal the tiles using two coats of Tile Doctor Colour Grow sealer
Read more
Large Victorian Hallway Restored in Gloucestershire
Victorian tiles are very hard-wearing and historically a popular choice for heavy traffic areas such as hallways. Still popular today
Read moreRepolishing Marble tiles in a Hallway
The owner of this polished Marble Tiled hallway at a house in Trowbridge was unhappy with the look of their floor which had become dull and scratched and wanted the floor re-polishing. Apologies in advance for the pictures below on reflection I should have taken some close-up shots so you could see the problem better. Cleaning Marble Tile and Grout The first step first was to give the floor a general clean focusing on the grout lines so I started by mixing a mild dilution of Tile Doctor Pro-Clean which is an alkaline based product that is safe to use on Marble. The solution was brushed around the floor concentrating on getting the product into the grout lines. I left this to dwell for 5-10 minutes before scrubbing with stiff grout brush. Once the grout lines were cleaned the dirty solution was removed with a wet vacuum and the tiles rinsed thoroughly with clean water. Polishing Marble Tiles The next step was to burnish the floor using a coarse diamond encrusted pad fitted to a rotary machine. This is used with clean water to remove surface scratches and any sealer that may be present. Once the water has turned to slurry after 4 passes of each tile I would remove with a wet vacuum and rinsed thoroughly. One that step was completed the process is repeated using the Medium,
Read more